r   e   k   l   a   m   a

bad sektory na dysku

Zaloguj się, aby obserwować  
Obserwujący 0

6 postów w tym temacie

Napisano

wyskoczył mi komunikat ze mam bad sektory:

xkhag6zewyluoezlr9u.png

więc wpisałem w terminalu:

sudo apt-get install smartmontools
aby zainstalowac program, następnie wpisałem:
sudo smartctl -a /dev/sda8
poniewaz podejrzewam że właśnie na sda8 są błędy, wyskoczyły dane:
darek@darek-laptop:~$ sudo smartctl -a /dev/sda8

smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen

Home page is http://smartmontools.sourceforge.net/


=== START OF INFORMATION SECTION ===

Model Family:     Western Digital Scorpio family

Device Model:     WDC WD1600BEVS-00RST0

Serial Number:    WD-WXE907002987

Firmware Version: 04.01G04

User Capacity:    160,041,885,696 bytes

Device is:        In smartctl database [for details use: -P show]

ATA Version is:   7

ATA Standard is:  Exact ATA specification draft version not indicated

Local Time is:    Fri Jan  1 19:59:31 2010 CET

SMART support is: Available - device has SMART capability.

SMART support is: Enabled


=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED


General SMART Values:

Offline data collection status:  (0x00)	Offline data collection activity

					was never started.

					Auto Offline Data Collection: Disabled.

Self-test execution status:      (   0)	The previous self-test routine completed

					without error or no self-test has ever 

					been run.

Total time to complete Offline 

data collection: 		 (7560) seconds.

Offline data collection

capabilities: 			 (0x7b) SMART execute Offline immediate.

					Auto Offline data collection on/off support.

					Suspend Offline collection upon new

					command.

					Offline surface scan supported.

					Self-test supported.

					Conveyance Self-test supported.

					Selective Self-test supported.

SMART capabilities:            (0x0003)	Saves SMART data before entering

					power-saving mode.

					Supports SMART auto save timer.

Error logging capability:        (0x01)	Error logging supported.

					General Purpose Logging supported.

Short self-test routine 

recommended polling time: 	 (   2) minutes.

Extended self-test routine

recommended polling time: 	 (  97) minutes.

Conveyance self-test routine

recommended polling time: 	 (   6) minutes.

SCT capabilities: 	       (0x103f)	SCT Status supported.

					SCT Feature Control supported.

					SCT Data Table supported.


SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE

  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       45

  3 Spin_Up_Time            0x0003   187   185   021    Pre-fail  Always       -       1625

  4 Start_Stop_Count        0x0032   096   096   000    Old_age   Always       -       4509

  5 Reallocated_Sector_Ct   0x0033   149   149   140    Pre-fail  Always       -       404

  7 Seek_Error_Rate         0x000f   100   253   051    Pre-fail  Always       -       0

  9 Power_On_Hours          0x0032   099   099   000    Old_age   Always       -       1296

 10 Spin_Retry_Count        0x0013   100   100   051    Pre-fail  Always       -       0

 11 Calibration_Retry_Count 0x0012   100   100   051    Old_age   Always       -       0

 12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1240

192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       431

193 Load_Cycle_Count        0x0032   193   193   000    Old_age   Always       -       21252

194 Temperature_Celsius     0x0022   117   097   000    Old_age   Always       -       30

196 Reallocated_Event_Count 0x0032   167   167   000    Old_age   Always       -       33

197 Current_Pending_Sector  0x0012   200   199   000    Old_age   Always       -       13

198 Offline_Uncorrectable   0x0010   100   253   000    Old_age   Offline      -       0

199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0

200 Multi_Zone_Error_Rate   0x0009   100   253   051    Pre-fail  Offline      -       0


SMART Error Log Version: 1

ATA Error Count: 490 (device log contains only the most recent five errors)

	CR = Command Register [HEX]

	FR = Features Register [HEX]

	SC = Sector Count Register [HEX]

	SN = Sector Number Register [HEX]

	CL = Cylinder Low Register [HEX]

	CH = Cylinder High Register [HEX]

	DH = Device/Head Register [HEX]

	DC = Device Command Register [HEX]

	ER = Error register [HEX]

	ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.


Error 490 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  01 51 00 66 86 b4 e1  Error: AMNF at LBA = 0x01b48666 = 28608102


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  c8 00 08 64 86 b4 01 00      00:51:18.428  READ DMA

  27 00 00 00 00 00 00 00      00:51:18.428  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 00 00      00:51:18.427  IDENTIFY DEVICE

  ef 03 46 00 00 00 00 00      00:51:18.427  SET FEATURES [Set transfer mode]

  27 00 00 00 00 00 00 00      00:51:18.390  READ NATIVE MAX ADDRESS EXT


Error 489 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  01 51 00 66 86 b4 e1  Error: AMNF at LBA = 0x01b48666 = 28608102


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  c8 00 08 64 86 b4 01 08      00:51:15.216  READ DMA

  27 00 00 00 00 00 00 08      00:51:15.215  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 00 08      00:51:15.215  IDENTIFY DEVICE

  ef 03 46 00 00 00 00 08      00:51:15.215  SET FEATURES [Set transfer mode]

  27 00 00 00 00 00 00 08      00:51:15.214  READ NATIVE MAX ADDRESS EXT


Error 488 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  01 51 00 66 86 b4 e1  Error: AMNF at LBA = 0x01b48666 = 28608102


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  c8 00 08 64 86 b4 01 08      00:51:12.362  READ DMA

  27 00 00 00 00 00 00 08      00:51:12.362  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 00 08      00:51:12.362  IDENTIFY DEVICE

  ef 03 46 00 00 00 00 08      00:51:12.362  SET FEATURES [Set transfer mode]

  27 00 00 00 00 00 00 08      00:51:12.361  READ NATIVE MAX ADDRESS EXT


Error 487 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  01 51 00 66 86 b4 e1  Error: AMNF at LBA = 0x01b48666 = 28608102


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  c8 00 08 64 86 b4 01 08      00:51:09.511  READ DMA

  27 00 00 00 00 00 00 08      00:51:09.510  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 00 08      00:51:09.510  IDENTIFY DEVICE

  ef 03 46 00 00 00 00 08      00:51:09.510  SET FEATURES [Set transfer mode]

  27 00 00 00 00 00 00 08      00:51:09.509  READ NATIVE MAX ADDRESS EXT


Error 486 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)

  When the command that caused the error occurred, the device was active or idle.


  After command completion occurred, registers were:

  ER ST SC SN CL CH DH

  -- -- -- -- -- -- --

  01 51 00 66 86 b4 e1  Error: AMNF at LBA = 0x01b48666 = 28608102


  Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name

  -- -- -- -- -- -- -- --  ----------------  --------------------

  c8 00 08 64 86 b4 01 08      00:51:06.659  READ DMA

  27 00 00 00 00 00 00 08      00:51:06.658  READ NATIVE MAX ADDRESS EXT

  ec 00 00 00 00 00 00 08      00:51:06.658  IDENTIFY DEVICE

  ef 03 46 00 00 00 00 08      00:51:06.658  SET FEATURES [Set transfer mode]

  27 00 00 00 00 00 00 08      00:51:06.658  READ NATIVE MAX ADDRESS EXT


SMART Self-test log structure revision number 1

No self-tests have been logged.  [To run self-tests, use: smartctl -t]



SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

    1        0        0  Not_testing

    2        0        0  Not_testing

    3        0        0  Not_testing

    4        0        0  Not_testing

    5        0        0  Not_testing

Selective self-test flags (0x0):

  After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 min

co robić ??

niestety domyślam sie dlaczego wyskoczyły... troche na sylwetra zaszaleliśmy i zacząłem walić w laptopa pięścią bo mi sie wieszał... to mogło być od tego

jakoś się tego nie da obejść np. czytałem coś że w miejsce nie bad sektorów nie robić partycji, poprostu je omijac

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Napisano

troche na sylwetra zaszaleliśmy i zacząłem walić w laptopa pięścią bo mi sie wieszał...

omgh :o

Polecam MHDD (live cd) chyba najlepszy program do diagnozy i ew. naprawy.

Możliwe że trzeba tylko naprawić sektory (jeśli faktycznie padły), jeśli nie to remap.

Wszystko ładnie opisane tutaj:

http://www.nirvanowiec.republika.pl/MHDD.html

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Napisano

ok, to mogłobyć od tego ?? :)

Udostępnij ten post


Link to postu
Udostępnij na innych stronach
r   e   k   l   a   m   a

Napisano

ok, to mogłobyć od tego

Mogło być od wszystkiego, zależy jak ciężka była Twoja pięść.

Generalnie z kręcącym się dyskiem należy obchodzić się jak z jajkiem a nie jak z przeciwnikiem.

Spróbuj jeszcze zrobić chkdsk z opcją automatycznie napraw uszkodzone sektory.

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Napisano

jeśli uszkodzenia są w jakimś konkretnym miejscu dysku i nie są za bardzo rozproszone to ja już tak robiłem, że obliczałem ile MB jest zdrowych potem ile trzeba zostawić bez partycji i znowu czysta partycja itd. niestety czasem może ci wyjść kilka partycji

i niema gwarancji, że dalej się nie posypie

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Napisano

podaj wartość parametru realocated sectour count

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Zaloguj się, aby skomentować

Będziesz mógł dodać komentarz po zalogowaniu się



Zaloguj się
Zaloguj się, aby obserwować  
Obserwujący 0