Witam otóż mam problem z komputerem. Dzisiaj mimo żadnych zmian od dawna (instalacji czego kolwiek) zaczął się zacinać gdy mam włączoną jaką kolwiek gre w trybie fullscreen. System w tym momencie jest swieżo po formacie (myślałem że to pomoże) ale problem dalej występuje. Objawia sie głównie tym ze po jakimś czasie grania 2-5minut zaczyna się zacinać myszka, dźwięk i cala reszta a po około 10-15 sekundach system restartuje się dodam tylko że jest to Windows 7 Ultimate x64. Niestety nie mam pojęcia co powinienem podać, jakie informacje aby jakoś ułatwić pomoc.
Wiec tak sa 4 pliki .dmp z czego 3 wygladaja podobnie (ten sam plik stwarza problem) :
A problem has been detected and Windows has been shut down to prevent damage
to your computer.
The problem seems to be caused by the following file: ntoskrnl.exe
If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.
Technical Information:
*** STOP: 0x00000124 (0x0000000000000000, 0xfffffa8007ddd8f8, 0x0000000000000000,
0x0000000000000000)
*** ntoskrnl.exe - Address 0xfffff80003306aec base at 0xfffff80002e54000 DateStamp
0x4ce7951a
i jeszcze jeden ktory wyglada tak:
A problem has been detected and Windows has been shut down to prevent damage
to your computer.
The problem seems to be caused by the following file: dump_atapi.sys
If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.
Technical Information:
*** STOP: 0x00000124 (0x0000000000000000, 0xfffffa8007d91388, 0x0000000000000000,
0x0000000000000000)
*** dump_atapi.sys - Address 0xfffff88003192730 base at 0xfffff880019b7000 DateStamp
0x4a5bc113
Dodam ze uzywalem WinDLG ktory nie pokazal zadnych bledow oraz Memtest ktory zacial mi komputer po jakims czasie.
Jesli mozna wiedziec czym sa te banki ? jestem kompletnie zielony jesli chodzi o co kolwiek zwiazanego z informatyka. Kosci przetestuje jak tylko wroce i zobaczymy czy to cos pomoze.
Bank, to inaczej miejsce na płycie głównej gdzie wpychasz kość ram… jeszcze inaczaj slot, gniazdo itd… przeczyść je spręzonym powietrzem lub pędzelkiem. Złącza na kościach pamięci możesz potraktować patyczkiem do uszu zamoczonym w spirytusie (tylko poczekać z wkładaniem aż wyschnie / odparuje).
Gniazdo i wtyczki hdd też potraktuj sprężonym powietrzem, ew silnie dmuchnij “z płuca”. Jeżeli masz taką możliwość, wymień kabel od dysku na inny.
wspomniany interface atapi odpowiada też za pracę cd-rom… jeżeli nie potrzebujesz, to odepnij i sprawdź czy bsody nadal występują.
Inna inszość, to że uwalona może być płyta główna i to ona powoduje błędy działania ww. urządzeń, jeżeli czyszczenie pomoże, to warto je sprawdzić na innym komputerze.
A problem has been detected and Windows has been shut down to prevent damage
to your computer.
The problem seems to be caused by the following file: hal.dll
IRQL_NOT_LESS_OR_EQUAL
If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.
Technical Information:
*** STOP: 0x0000000a (0xfffff8a00b4a0808, 0x0000000000000002, 0x0000000000000001,
0xfffff80002e201ae)
*** hal.dll - Address 0xfffff80002e201ae base at 0xfffff80002e03000 DateStamp
0x4ce7c669
A problem has been detected and Windows has been shut down to prevent damage
to your computer.
The problem seems to be caused by the following file: ntoskrnl.exe
INTERNAL_POWER_ERROR
If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow
these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.
Technical Information:
*** STOP: 0x000000a0 (0x000000000000000b, 0x00000000bfe96000, 0x0000000000000003,
0x000000001934a000)
*** ntoskrnl.exe - Address 0xfffff80002e9b640 base at 0xfffff80002e1b000 DateStamp
0x4ce7951a
Jakis power error nie wiem co mam przez to rozumiec
Szczerze ? przeczyscilem wszystko itd. nie pomagalo, ale po dniu-dwoch samo sie naprawilo i narazie nie ma zadnych bledow ;D tak czy siak dziekuje za pomoc