Nie wiem jak włożyć ram do płyty głównej ASUS A8NE-FM/S są cztery wejscia i nie wiem pod które podpiąć ram. Mam instrukcje ale po angielsku może ktoś zna 
,1.4 System memory
1.4.1 1.4.1 1.4.1 1.4.1 1.4.1 Overview Overview Overview Overview Overview
The motherboard comes with four 184-pin Double Data Rate
Inline Memory Modules (DIMM) sockets.
The following figure illustrates the location of the sockets: (obrazki)
,1.4.2 1.4.2 1.4.2 1.4.2 1.4.2 Memory configurations Memory configurations Memory configurations Memory configurations Memory configurations
You may install 256 MB, 512 MB and 1 GB unbuffered non-ECC DDR DIMMs
into the DIMM sockets using the memory configurations in this section.
Channel Channel Channel Channel Channel Sockets Sockets Sockets Sockets Sockets
Channel A DIMM_A1 and DIMM_B1
Channel B DIMM_A2 and DIMM_B2
• For dual-channel configuration, the total size of memory module(s) installed
per channel must be the same for better performance
(DIMM_A1+DIMM_B1=DIMM_A2+DIMM_B2).
• Always install DIMMs with the same CAS latency. For optimum
compatibility, we recommend that you obtain memory modules from
the same vendor. Refer to the DDR400 Qualified Vendors List on the
next page for details.
• Due to chipset resource allocation, the system may detect less than
4 GB of system memory when you installed four 1 GB DDR memory
modules.
• Due to chipset limitation, this motherboard does not support DIMM
modules with 128 Mb memory chips or double-sided x16 memory chips.
• With the 4 DIMM slot, the DIMM slots DIMM_A2 and DIMM_B2 are always to
be populated in pairs.’"
,1.4.3 1.4.3 1.4.3 1.4.3 1.4.3 Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM
- Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
- Unlock a DIMM socket by
pressing the retaining clips
outward.
- Align a DIMM on the socket such
that the notch on the DIMM
matches the break on the
socket.
Locked retaining clip Locked retaining clip Locked retaining clip Locked retaining clip Locked retaining clip
Make sure to unplug the power supply before adding or removing DIMMs
or other system components. Failure to do so may cause severe damage
to both the motherboard and the components.
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip Unlocked retaining clip
DDR DIMM notch DDR DIMM notch DDR DIMM notch DDR DIMM notch DDR DIMM notch
1
2
1’’
,1.4.4 1.4.4 1.4.4 1.4.4 1.4.4 Removing a DIMM Removing a DIMM Removing a DIMM Removing a DIMM Removing a DIMM
To remove a DIMM:
- Simultaneously press the
retaining clips outward to unlock
the DIMM.
- Remove the DIMM from the socket.
Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.
DDR DIMM notch DDR DIMM notch DDR DIMM notch DDR DIMM notch DDR DIMM notch 1
2
1""
Jeżeli sie komuś chce tłumaczyć to wielkie dzięki:) tutaj wypisze tylko ostrzeżenia które chyba najbardziej mi sie przydadzą.
Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM Installing a DIMM
Make sure to unplug the power supply before adding or removing DIMMs
or other system components. Failure to do so may cause severe damage
to both the motherboard and the components.
A DDR DIMM is keyed with a notch so that it fits in only one direction
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.
