This image was saved from this machine with hard drive S.M.A.R.T. info at 2021-0210-1617: *****************************************************. For the drive: /dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-2-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: SSDPR-CX400-256 Serial Number: RW7005770 Firmware Version: SBFM61.3 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 10 16:17:35 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 81765 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 29 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 102 168 SATA_Phy_Error_Count 0x0012 100 100 000 Old_age Always - 0 170 Bad_Blk_Ct_Erl/Lat 0x0003 068 068 010 Pre-fail Always - 43/59 173 MaxAvgErase_Ct 0x0012 100 100 000 Old_age Always - 8 (Average 1) 192 Unsafe_Shutdown_Count 0x0012 100 100 000 Old_age Always - 51 194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33) 218 CRC_Error_Count 0x000b 100 100 050 Pre-fail Always - 2 231 SSD_Life_Left 0x0013 100 100 000 Pre-fail Always - 99 241 Lifetime_Writes_GiB 0x0012 100 100 000 Old_age Always - 428 SMART Error Log Version: 1 ATA Error Count: 36618 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 36618 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 06 e2 93 0f e0 Error: UNC 6 sectors at LBA = 0x000f93e2 = 1020898 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 06 e2 93 0f e0 08 00:02:54.012 READ DMA ef 10 02 00 00 00 a0 08 00:02:54.012 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 00:02:54.012 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 00:02:54.012 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:54.012 SET FEATURES [Set transfer mode] Error 36617 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 e1 93 0f e0 Error: UNC 1 sectors at LBA = 0x000f93e1 = 1020897 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 e1 93 0f e0 08 00:02:53.988 READ DMA ef 10 02 00 00 00 a0 08 00:02:53.988 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 00:02:53.988 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 00:02:53.988 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:53.988 SET FEATURES [Set transfer mode] Error 36616 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 e0 93 0f e0 Error: UNC 1 sectors at LBA = 0x000f93e0 = 1020896 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 e0 93 0f e0 08 00:02:53.965 READ DMA ef 10 02 00 00 00 a0 08 00:02:53.965 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 00:02:53.965 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 00:02:53.965 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:53.965 SET FEATURES [Set transfer mode] Error 36615 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 06 e2 93 0f e0 Error: UNC 6 sectors at LBA = 0x000f93e2 = 1020898 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 06 e2 93 0f e0 08 00:02:53.941 READ DMA ef 10 02 00 00 00 a0 08 00:02:53.941 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 00:02:53.941 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 00:02:53.941 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:53.941 SET FEATURES [Set transfer mode] Error 36614 occurred at disk power-on lifetime: 22 hours (0 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 e1 93 0f e0 Error: UNC 1 sectors at LBA = 0x000f93e1 = 1020897 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 e1 93 0f e0 08 00:02:53.917 READ DMA ef 10 02 00 00 00 a0 08 00:02:53.917 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 00:02:53.917 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 00:02:53.917 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:53.917 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 1099511627776 10484942882471936 Not_testing 2 72057594037938270 4611686018427387904 Not_testing 3 680984613 1073742848 Not_testing 4 44921065390080 16777216 Not_testing 5 2943946941404282880 1099511627776 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.