wyskoczył mi komunikat ze mam bad sektory:
więc wpisałem w terminalu:
sudo apt-get install smartmontools
aby zainstalowac program, następnie wpisałem:
sudo smartctl -a /dev/sda8
poniewaz podejrzewam że właśnie na sda8 są błędy, wyskoczyły dane:
darek@darek-laptop:~$ sudo smartctl -a /dev/sda8
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio family
Device Model: WDC WD1600BEVS-00RST0
Serial Number: WD-WXE907002987
Firmware Version: 04.01G04
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jan 1 19:59:31 2010 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (7560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 97) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 45
3 Spin_Up_Time 0x0003 187 185 021 Pre-fail Always - 1625
4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4509
5 Reallocated_Sector_Ct 0x0033 149 149 140 Pre-fail Always - 404
7 Seek_Error_Rate 0x000f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1296
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1240
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 431
193 Load_Cycle_Count 0x0032 193 193 000 Old_age Always - 21252
194 Temperature_Celsius 0x0022 117 097 000 Old_age Always - 30
196 Reallocated_Event_Count 0x0032 167 167 000 Old_age Always - 33
197 Current_Pending_Sector 0x0012 200 199 000 Old_age Always - 13
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 490 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 490 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 66 86 b4 e1 Error: AMNF at LBA = 0x01b48666 = 28608102
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 64 86 b4 01 00 00:51:18.428 READ DMA
27 00 00 00 00 00 00 00 00:51:18.428 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00:51:18.427 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 00:51:18.427 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00:51:18.390 READ NATIVE MAX ADDRESS EXT
Error 489 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 66 86 b4 e1 Error: AMNF at LBA = 0x01b48666 = 28608102
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 64 86 b4 01 08 00:51:15.216 READ DMA
27 00 00 00 00 00 00 08 00:51:15.215 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:51:15.215 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:51:15.215 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 08 00:51:15.214 READ NATIVE MAX ADDRESS EXT
Error 488 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 66 86 b4 e1 Error: AMNF at LBA = 0x01b48666 = 28608102
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 64 86 b4 01 08 00:51:12.362 READ DMA
27 00 00 00 00 00 00 08 00:51:12.362 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:51:12.362 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:51:12.362 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 08 00:51:12.361 READ NATIVE MAX ADDRESS EXT
Error 487 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 66 86 b4 e1 Error: AMNF at LBA = 0x01b48666 = 28608102
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 64 86 b4 01 08 00:51:09.511 READ DMA
27 00 00 00 00 00 00 08 00:51:09.510 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:51:09.510 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:51:09.510 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 08 00:51:09.509 READ NATIVE MAX ADDRESS EXT
Error 486 occurred at disk power-on lifetime: 1295 hours (53 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 66 86 b4 e1 Error: AMNF at LBA = 0x01b48666 = 28608102
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 64 86 b4 01 08 00:51:06.659 READ DMA
27 00 00 00 00 00 00 08 00:51:06.658 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 00:51:06.658 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:51:06.658 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 08 00:51:06.658 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 min
co robić ??
niestety domyślam sie dlaczego wyskoczyły… troche na sylwetra zaszaleliśmy i zacząłem walić w laptopa pięścią bo mi sie wieszał… to mogło być od tego
jakoś się tego nie da obejść np. czytałem coś że w miejsce nie bad sektorów nie robić partycji, poprostu je omijac