Dysk twardy uszkodzony?Rozwiązany


(And2352) #1

Witam.Proszę o sprawdzenie smart dysku. Dysk padł całkiem.Temat do zamknięcia.

 

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 2.5" HDD MK..65GSX
Device Model:     TOSHIBA MK3265GSX
Serial Number:    70P7C6G6T
LU WWN Device Id: 5 000039 2a360a344
Firmware Version: GJ002H
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Thu Aug 11 10:40:03 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (  120) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      ( 104) minutes.
SCT capabilities:            (0x003d)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1123
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       2947
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       286
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   091   091   000    Old_age   Always       -       3978
 10 Spin_Retry_Count        0x0033   158   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       2929
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       42
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       76
193 Load_Cycle_Count        0x0032   095   095   000    Old_age   Always       -       57249
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       33 (Min/Max 9/45)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       145
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       557
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       1
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       53
222 Loaded_Hours            0x0032   093   093   000    Old_age   Always       -       3116
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       332
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 2672 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2672 occurred at disk power-on lifetime: 3978 hours (165 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 0a 9e 58 42 60  Error: UNC at LBA = 0x0042589e = 4348062

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 01 08 9e 58 42 40 08      00:34:23.459  READ FPDMA QUEUED
  60 01 00 9f 58 42 40 08      00:34:23.459  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      00:34:23.459  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 e0 00      00:34:23.459  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 00      00:34:23.458  IDENTIFY DEVICE

Error 2671 occurred at disk power-on lifetime: 3978 hours (165 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 02 9d 58 42 60  Error: UNC at LBA = 0x0042589d = 4348061

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 01 10 9f 58 42 40 08      00:34:15.648  READ FPDMA QUEUED
  60 01 08 9e 58 42 40 08      00:34:15.648  READ FPDMA QUEUED
  60 01 00 9d 58 42 40 08      00:34:15.648  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      00:34:15.648  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 e0 00      00:34:15.648  READ NATIVE MAX ADDRESS EXT

Error 2670 occurred at disk power-on lifetime: 3978 hours (165 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 1a 9c 58 42 60  Error: UNC at LBA = 0x0042589c = 4348060

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 01 18 9c 58 42 40 08      00:34:07.848  READ FPDMA QUEUED
  60 01 10 9d 58 42 40 08      00:34:07.848  READ FPDMA QUEUED
  60 01 08 9e 58 42 40 08      00:34:07.848  READ FPDMA QUEUED
  60 01 00 9f 58 42 40 08      00:34:07.848  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      00:34:07.847  SET FEATURES [Reserved for Serial ATA]

Error 2669 occurred at disk power-on lifetime: 3978 hours (165 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 02 9b 58 42 60  Error: UNC at LBA = 0x0042589b = 4348059

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 01 20 9f 58 42 40 08      00:34:00.036  READ FPDMA QUEUED
  60 01 18 9e 58 42 40 08      00:34:00.036  READ FPDMA QUEUED
  60 01 10 9d 58 42 40 08      00:34:00.036  READ FPDMA QUEUED
  60 01 08 9c 58 42 40 08      00:34:00.036  READ FPDMA QUEUED
  60 01 00 9b 58 42 40 08      00:34:00.036  READ FPDMA QUEUED

Error 2668 occurred at disk power-on lifetime: 3978 hours (165 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 41 2a 9a 58 42 60  Error: UNC at LBA = 0x0042589a = 4348058

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 01 28 9a 58 42 40 08      00:33:52.225  READ FPDMA QUEUED
  60 01 20 9b 58 42 40 08      00:33:52.225  READ FPDMA QUEUED
  60 01 18 9c 58 42 40 08      00:33:52.225  READ FPDMA QUEUED
  60 01 10 9d 58 42 40 08      00:33:52.225  READ FPDMA QUEUED
  60 01 08 9e 58 42 40 08      00:33:52.225  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      3968         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.