Próbowałem uruchomić ten modem pod linuxem. W tym celu zainstalowałem ręcznie:
- libwvstreams
- libwvstreams-extras
- libuniconf
Z tej strony : http://packages.ubuntu.com/
Następnie wvdial_1.61-4.1_i386.deb
stąd http://archive.ubuntu.com/ubuntu/pool/main/w/wvdial/
wvdial.conf ustawiłem tak:
[Dialer play]
Modem = /dev/ttyUSB0
Baud = 57600
Init1 = ATH
Init2 = ATE1
Init3 = AT+CGDCONT=1,"IP","internet"
Dial Command = ATD
Phone = *99#
Stupid mode = yes
Username = "internet"
Password = "internet"
Auto DNS = yes
Po wpisaniu komendy “sudo wvdial play” następuje próba połączenia ale nieudana. Poniżej zamieszczam log dla wvdial z /var/log/messages:
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3 S4 S5 S6 S7 S8
Modem Port Scan<*1>: S9 S10 S11 S12 S13 S14 S15 S16
Modem Port Scan<*1>: S17 S18 S19 S20 S21 S22 S23 S24
Modem Port Scan<*1>: S25 S26 S27 S28 S29 S30 S31
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- +CME ERROR: 50
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &D2 -- +CME ERROR: 50
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 +FCLASS=0 -- +CME ERROR: 50
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &C1 -- +CME ERROR: 50
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 &D2 -- +CME ERROR: 50
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 +FCLASS=0 -- +CME ERROR: 50
ttyUSB1<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB1<*1>: Speed 9600: AT -- OK
ttyUSB1<*1>: Max speed is 9600; that should be safe.
ttyUSB1<*1>: ATQ0 V1 E1 S0=0 -- OK
Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0"
ttyUSB1<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0"
Co robię źle?
