Witam!
Mam chyba problem z dyskiem.
Pojawia mi się komunikat z plikiem hal.dll , że jest uszkodzony i trzeba go zasąpic lub skopiowac. Gdy wszedłem do konsoli odzyskiwania to tak jakbym nie było instalacji na dysku. Próbowałem różnych rzeczy… nie mogę zrobic chkdsk bo wyskakuje komunikat że na dysku jest co najmniej jeden błąd na dysku. Przy innych opcjach pisze “odmowa dostępu”. Chciałem naprawic instalacje przez instaluj -> F8 -> R ale nie ma instalacji. Poza tym format plików poszczególnych partycji raz jako nieznany raz jako nfts.
Proszę o pomoc bo nie wiem co w tym momencie mam robic.
smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Copyright © 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.2 series
Device Model: ST98823A
Serial Number: 5PK0X8HB
Firmware Version: 3.04
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Fri Feb 11 22:26:00 2011 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 426) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SCT capabilities: (0x0001) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2947
5 Reallocated_Sector_Ct 0x0033 089 089 036 Pre-fail Always - 442
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 4630040161
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 10615
10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2944
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 48542
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 036 045 Old_age Always In_the_past 33 (6 89 33 29)
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 2206
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 215056
194 Temperature_Celsius 0x0022 033 064 000 Old_age Always - 33 (0 12 0 0)
195 Hardware_ECC_Recovered 0x001a 075 051 000 Old_age Always - 123483055
197 Current_Pending_Sector 0x0012 093 093 000 Old_age Always - 154
198 Offline_Uncorrectable 0x0010 093 093 000 Old_age Offline - 154
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1081 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It “wraps” after 49.710 days.
Error 1081 occurred at disk power-on lifetime: 10615 hours (442 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 e7 58 04 e1 Error: UNC 8 sectors at LBA = 0x010458e7 = 17062119
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 e7 58 04 e1 00 00:05:12.688 READ DMA
27 00 00 00 00 00 e0 00 00:05:12.631 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:05:12.628 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:05:12.625 SET FEATURES [set transfer mode]
27 00 00 00 00 00 e0 00 00:05:12.625 READ NATIVE MAX ADDRESS EXT
Error 1080 occurred at disk power-on lifetime: 10615 hours (442 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 e7 58 04 e1 Error: UNC 8 sectors at LBA = 0x010458e7 = 17062119
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 e7 58 04 e1 00 00:05:08.714 READ DMA
27 00 00 00 00 00 e0 00 00:05:08.714 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:05:08.711 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:05:06.817 SET FEATURES [set transfer mode]
27 00 00 00 00 00 e0 00 00:05:06.776 READ NATIVE MAX ADDRESS EXT
Error 1079 occurred at disk power-on lifetime: 10615 hours (442 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 e7 58 04 e1 Error: UNC 8 sectors at LBA = 0x010458e7 = 17062119
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 e7 58 04 e1 00 00:05:08.714 READ DMA
27 00 00 00 00 00 e0 00 00:05:08.714 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:05:08.711 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:05:06.817 SET FEATURES [set transfer mode]
27 00 00 00 00 00 e0 00 00:05:06.776 READ NATIVE MAX ADDRESS EXT
Error 1078 occurred at disk power-on lifetime: 10615 hours (442 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 e7 58 04 e1 Error: UNC 8 sectors at LBA = 0x010458e7 = 17062119
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 e7 58 04 e1 00 00:05:02.933 READ DMA
27 00 00 00 00 00 e0 00 00:05:02.889 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:05:02.885 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:05:06.817 SET FEATURES [set transfer mode]
27 00 00 00 00 00 e0 00 00:05:06.776 READ NATIVE MAX ADDRESS EXT
Error 1077 occurred at disk power-on lifetime: 10615 hours (442 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 e7 58 04 e1 Error: UNC 8 sectors at LBA = 0x010458e7 = 17062119
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 e7 58 04 e1 00 00:05:02.933 READ DMA
27 00 00 00 00 00 e0 00 00:05:02.889 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 00:05:02.885 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 02 00:05:02.883 SET FEATURES [set transfer mode]
27 00 00 00 00 00 e0 00 00:05:02.883 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.