net9
(Net9)
29 Grudzień 2012 18:05
#1
Witam
Mam netbooka Samsung n210, kiedyś zmieniłem dysk twardy który się zepsuł i komputer zwolnił strasznie, filmy na yt na 480p się zacinały i praktycznie każda aplikacja. Dysk pochodził z startego laptopa Emachines e510 i znów się zepsuł :-|… Zamierzam zmienić teraz dysk na 320 gb i mam pytanie, czy po zmianie dysku na nowy komputer może przestać się tak zawieszać, czy będzie dalej tak chodził?
I druga sprawa. Chcę także zmienić pamięć ram z 1 gb na 2 gb, tylko niewiem na jaką. Na co patrzeć przy zakupie ramu?
Proszę o szybką pomoc gdyż do poniedziałku muszę wiedzieć czy opłaca się coś zmieniać czy kupić nowy, lecz wolałbym zostać przy pierwszej opcji Jeśli trzeba napisać specyfikację mam wszystko pod ręką
PC2-5300 DDR2-667 200pin SDRAM SODIMM takie coś w niego pakują i to działa
Musisz kupić jedną kość 2GB ponieważ masz tam tylko jeden slot na pamięci.
Co do dysku to może ten stary miał badsectory ?
net9
(Net9)
29 Grudzień 2012 19:54
#3
To to nie może być jakaś bylejaka nowa karta DDR2 2048 mb?
Badsectory to nie są, próbowałem włączyć instalację windowsa i w niej wykrywa tylko dysk jako jedną całość, jakieś 149 gb. Właśnie piszę z niego z Parted Magic (strasznie długo się włącząło w przeciwieństwie do tego jak działał dysk)i tutaj wogóle nie chce wejść do dysku. Miałem tam kilkanaście giga zdjęć
ra-v
(ra-v)
29 Grudzień 2012 19:57
#4
Nie ma żadnej gwarancji.
To że 480p mulił to może jest wina sterowników grafiki lub 1-rdzeniowego procesora. To że cały system muli to przez śmietnik w systemie.
Na to czy laptop obsłuży tyle RAM (CPU na pewno tak), i czy są tego samego typu (czyli pewnie jakieś DDR2 SO DIMM).
Czy się opłaca oceń sam, nie znam twoich funduszy.
2 GB RAM SO DIMM to pewnie wydatek ok 100 zł za nową oryginalną sztukę. Dysk nie wiem, pewnie z 200-250zł za nowy. Używane dziel nawet na dwa.
net9
(Net9)
29 Grudzień 2012 20:06
#5
System był na nowo zainstalowany po zmianie dysku i później jeszcze dwa razy jak działał, po zmianie dysku zaczęło mulić, więc to raczej nie wina śmietnika i sterowników bo robiłem wiele kombinacji z wersjami sterowników, flasha i przeglądarek. Koszt nowego dysku i ram do około 230 zł więc wydaje mi się to dobrą opcją tylko obawiam się mulenia…
Na pierwszym dysku chodziło yt 720p a muliło lekko na 1080 dopiero ;]
Teraz po włączeniu komputera przez jakiś czas w dysku coś przeskakuje w równych odstępach czasu. Da się może coś naprawić w parted magic? ![-o<
ra-v
(ra-v)
29 Grudzień 2012 20:22
#6
Przez dysk grafika nie muli.
Sprawdź dysk HD Tunem i pokaż co pokazuje SMART, test szybkości i czy są błędne sektory.
net9
(Net9)
29 Grudzień 2012 20:27
#7
Jakby to powiedzieć… nie mam jak tego włączyć bo jestem na linuxie a nie mam innego kompa
Może w Parted Magic można coś takiego wykonać?
falcon89
(falcon89)
29 Grudzień 2012 20:44
#8
Można sprawadzić SMART na Parted Magic (kliknij Smart Control) http://techexposures.com/wp-content/upl … ontrol.png
net9
(Net9)
29 Grudzień 2012 20:48
#9
Może mnie ktoś poinstruować co mam w tym wykonać?
Edit:
Niewiem czy o to chodzi, ale znalazłem opcję robienia logu i są tam trzy punkty, wklejam trzeci bo jest tego najwięcej:
v/sda’
3. ‘smartctl’ -H -i -c -A -l error -l selftest -l selective '/de smartctl 6.0 2012-10-10 r3643 [i686-linux-3.5.6-pmagic] (local build) Copyright © 2002-12, Bruce Allen, Christian Franke, http://www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MK1646GSX Serial Number: 58FMCGKUT LU WWN Device Id: 5 000039 103d85235 Firmware Version: LB113J User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Sat Dec 29 20:47:52 2012 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Read SMART Thresholds failed: scsi error aborted command === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 — Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 — Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 — Pre-fail Always - 1670 4 Start_Stop_Count 0x0032 100 100 — Old_age Always - 5074 5 Reallocated_Sector_Ct 0x0033 076 076 — Pre-fail Always - 1896 7 Seek_Error_Rate 0x000b 100 100 — Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 — Pre-fail Offline - 0 9 Power_On_Hours 0x0032 089 089 — Old_age Always - 4584 10 Spin_Retry_Count 0x0033 200 100 — Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 — Old_age Always - 3887 192 Power-Off_Retract_Count 0x0032 099 099 — Old_age Always - 778 193 Load_Cycle_Count 0x0032 090 090 — Old_age Always - 107918 194 Temperature_Celsius 0x0022 100 100 — Old_age Always - 42 (Min/Max 8/56) 196 Reallocated_Event_Count 0x0032 100 100 — Old_age Always - 183 197 Current_Pending_Sector 0x0032 100 100 — Old_age Always - 135 198 Offline_Uncorrectable 0x0030 100 100 — Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 253 — Old_age Always - 13 220 Disk_Shift 0x0002 100 100 — Old_age Always - 106 222 Loaded_Hours 0x0032 092 092 — Old_age Always - 3401 223 Load_Retry_Count 0x0032 096 096 — Old_age Always - 42 224 Load_Friction 0x0022 100 100 — Old_age Always - 0 226 Load-in_Time 0x0026 100 100 — Old_age Always - 316 240 Head_Flying_Hours 0x0001 100 100 — Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 11139 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It “wraps” after 49.710 days. Error 11139 occurred at disk power-on lifetime: 4581 hours (190 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH – -- – -- – -- – 40 41 8a 54 19 aa 6a Error: UNC at LBA = 0x0aaa1954 = 178919764 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name – -- – -- – -- – -- ---------------- -------------------- 60 40 88 17 19 aa 40 00 00:23:51.575 READ FPDMA QUEUED 60 7b 70 78 c6 5a 40 00 00:23:51.542 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:23:51.541 READ LOG EXT 61 08 60 f8 42 b2 40 00 00:23:47.454 WRITE FPDMA QUEUED 61 08 58 b8 21 b3 40 00 00:23:47.453 WRITE FPDMA QUEUED Error 11138 occurred at disk power-on lifetime: 4581 hours (190 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH – -- – -- – -- – 40 41 3a 54 19 aa 6a Error: WP at LBA = 0x0aaa1954 = 178919764 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name – -- – -- – -- – -- ---------------- -------------------- 61 08 60 f8 42 b2 40 00 00:23:47.454 WRITE FPDMA QUEUED 61 08 58 b8 21 b3 40 00 00:23:47.453 WRITE FPDMA QUEUED 61 08 50 88 49 b6 40 00 00:23:47.453 WRITE FPDMA QUEUED 61 07 48 10 7b 6c 40 00 00:23:47.453 WRITE FPDMA QUEUED 60 7b 40 78 c6 5a 40 00 00:23:47.453 READ FPDMA QUEUED Error 11137 occurred at disk power-on lifetime: 4581 hours (190 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH – -- – -- – -- – 40 41 1a 54 19 aa 6a Error: UNC at LBA = 0x0aaa1954 = 178919764 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name – -- – -- – -- – -- ---------------- -------------------- 60 f8 20 80 c5 5a 40 00 00:23:43.434 READ FPDMA QUEUED 60 40 18 17 19 aa 40 00 00:23:43.434 READ FPDMA QUEUED 60 08 00 78 c5 5a 40 00 00:23:43.397 READ FPDMA QUEUED 60 80 f8 20 7b d9 40 00 00:23:43.397 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:23:43.396 READ LOG EXT Error 11136 occurred at disk power-on lifetime: 4581 hours (190 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH – -- – -- – -- – 40 41 8a 54 19 aa 6a Error: WP at LBA = 0x0aaa1954 = 178919764 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name – -- – -- – -- – -- ---------------- -------------------- 61 08 e8 00 43 b2 40 00 00:23:39.344 WRITE FPDMA QUEUED 61 10 e0 9a fa 7b 40 00 00:23:39.344 WRITE FPDMA QUEUED 61 08 d8 92 fa 7b 40 00 00:23:39.344 WRITE FPDMA QUEUED 61 08 d0 8a fa 7b 40 00 00:23:39.343 WRITE FPDMA QUEUED 61 08 c8 82 fa 7b 40 00 00:23:39.343 WRITE FPDMA QUEUED Error 11135 occurred at disk power-on lifetime: 4581 hours (190 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH – -- – -- – -- – 40 41 62 54 19 aa 6a Error: UNC at LBA = 0x0aaa1954 = 178919764 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name – -- – -- – -- – -- ---------------- -------------------- 60 08 70 18 7b d9 40 00 00:23:35.290 READ FPDMA QUEUED 61 10 68 a8 21 b3 40 00 00:23:35.290 WRITE FPDMA QUEUED 60 40 60 17 19 aa 40 00 00:23:35.290 READ FPDMA QUEUED 60 09 48 a0 a0 56 40 00 00:23:35.263 READ FPDMA QUEUED 60 08 40 d0 cc b6 40 00 00:23:35.263 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
ra-v
(ra-v)
30 Grudzień 2012 00:10
#10
Nie wiem jak wg was, ale wg mnie i wg tych danych coś się dzieje ze strukturą fizyczną dysku.
W Linuxie masz program palimpsest, nazwany w menu “Narzędzie do obsługi dysków”
Zrób taki test
net9
(Net9)
30 Grudzień 2012 14:20
#11
Przeszukałem i pouruchamiałem wszystkie dostępne aplikacje i nie mam tu takiego czegoś chyba, że coś przeoczyłem.
ra-v
(ra-v)
31 Grudzień 2012 01:11
#12
Pakiet nazywa się niby gnome-disk-utility
http://en.wikipedia.org/wiki/GNOME_Disks
Przynajmniej takie coś jest na systemach bazujących RPM, a wielce prawdopodobnie że na systemach z GNOME, więc możesz ściągnąć Live CD i sprawdzić.