Ubuntu 12.04 nie chce się połączyć z siecią przewodową

Witam

Od niedawna jestem posiadaczem Linuxa w swoim laptopie. Niestety mam problem, gdyż nie mogę się podłączyć do internetu za pomocą tzw kabla. Linux wykrywa tylko połączenie lecz ciągle nie może się połączyć z internetem. Będę bardzo wdzięczny za pomoc :slight_smile:

Napisz coś więcej o swoim dostawcy internetu. Możliwe, że musisz ustawić statyczny adres IP.

Jednym dostawcą internetu jest sieć osiedlowa(IST- istsc.pl ) natomiast drugi przypadek jest z mieszkaniem w akademiku. Mając Windowsa 7 wszystko działało bez problemu. WiFi działa bez żadnych problemów natomiast podczas łączenia z sieciową przewodową Ubuntu znajduje normalnie sieć próbuje nawiązac połączenie, ale bezskutecznie.

Uzyskujesz w ogóle adres IP? Uruchom terminal i podaj wyniki poniższych poleceń.

ifconfig

nm-tool

route -n

ping -c 4 dobreprogramy.pl

traceroute dobreprogramy.pl

Co to ma do rzeczy?

Podaj jeszcze wynik polecenia:

lspci -k
eth0 Link encap:Ethernet HWaddr 28:92:4a:3f:6f:2b  

          UP BROADCAST MULTICAST MTU:1500 Metric:1

          RX packets:8178 errors:0 dropped:0 overruns:0 frame:0

          TX packets:898 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:597505 (597.5 KB) TX bytes:197486 (197.4 KB)

          Interrupt:47 Base address:0x8000 


lo Link encap:Local Loopback  

          inet addr:127.0.0.1 Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING MTU:16436 Metric:1

          RX packets:35791 errors:0 dropped:0 overruns:0 frame:0

          TX packets:35791 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:3031325 (3.0 MB) TX bytes:3031325 (3.0 MB)


wlan0 Link encap:Ethernet HWaddr 74:e5:43:8f:39:a2  

          inet addr:172.16.67.247 Bcast:172.16.255.255 Mask:255.255.0.0

          inet6 addr: fe80::76e5:43ff:fe8f:39a2/64 Scope:Link

          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

          RX packets:888464 errors:0 dropped:0 overruns:0 frame:0

          TX packets:680302 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:1058240614 (1.0 GB) TX bytes:73893394 (73.8 MB)

NetworkManager Tool


State: connected (global)


- Device: eth0 -----------------------------------------------------------------

  Type: Wired

  Driver: r8169

  State: unavailable

  Default: no

  HW Address: 28:92:4A:3F:6F:2B


  Capabilities:

    Carrier Detect: yes

    Speed: 100 Mb/s


  Wired Properties

    Carrier: off



- Device: wlan0 [PWR-WiFi] ----------------------------------------------------

  Type: 802.11 WiFi

  Driver: ath9k

  State: connected

  Default: yes

  HW Address: 74:E5:43:8F:39:A2


  Capabilities:

    Speed: 54 Mb/s


  Wireless Properties

    WEP Encryption: yes

    WPA Encryption: yes

    WPA2 Encryption: yes


  Wireless Access Points (* = current AP)

    eduroam: Infra, 00:19:AA:77:27:91, Freq 2437 MHz, Rate 54 Mb/s, Strength 74 WPA2 Enterprise

    eduroam: Infra, 00:19:AA:77:24:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 34 WPA2 Enterprise

    eduroam: Infra, 00:19:AA:77:27:71, Freq 2412 MHz, Rate 54 Mb/s, Strength 39 WPA2 Enterprise

    PWR-WiFi: Infra, 00:19:AA:77:24:60, Freq 2462 MHz, Rate 54 Mb/s, Strength 45

    PWR-WiFi: Infra, 00:19:AA:77:27:70, Freq 2412 MHz, Rate 54 Mb/s, Strength 22

    *PWR-WiFi: Infra, 00:19:AA:77:27:90, Freq 2437 MHz, Rate 54 Mb/s, Strength 60

    TNM-PWR: Infra, 00:24:01:67:27:B9, Freq 2447 MHz, Rate 54 Mb/s, Strength 15 WPA2

    PWR-WiFi: Infra, 00:19:AA:77:24:80, Freq 2412 MHz, Rate 54 Mb/s, Strength 22


  IPv4 Settings:

    Address: 172.16.67.247

    Prefix: 16 (255.255.0.0)

    Gateway: 172.16.0.1

Destination Gateway Genmask Flags Metric Ref Use Iface

0.0.0.0 172.16.0.1 0.0.0.0 UG 0 0 0 wlan0

169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0

172.16.0.0 0.0.0.0 255.255.0.0 U 2 0 0 wlan0

PING dobreprogramy.pl (194.0.171.150) 56(84) bytes of data.

64 bytes from nlb-web.xenium.pl (194.0.171.150): icmp_req=1 ttl=116 time=47.7 ms

64 bytes from nlb-web.xenium.pl (194.0.171.150): icmp_req=2 ttl=116 time=43.9 ms

64 bytes from nlb-web.xenium.pl (194.0.171.150): icmp_req=3 ttl=116 time=45.2 ms

64 bytes from nlb-web.xenium.pl (194.0.171.150): icmp_req=4 ttl=116 time=44.6 ms


--- dobreprogramy.pl ping statistics ---

4 packets transmitted, 4 received, 0% packet loss, time 3005ms

rtt min/avg/max/mdev = 43.946/45.401/47.787/1.448 ms

00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Complex

	Subsystem: Hewlett-Packard Company Device 1849

00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Device 9990

	Subsystem: Hewlett-Packard Company Device 1849

00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel modules: snd-hda-intel

00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Port

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:10.0 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: xhci_hcd

00:10.1 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: xhci_hcd

00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller [AHCI mode]

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ahci

00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ehci_hcd

00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ehci_hcd

00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 14)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel modules: i2c-piix4

00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: snd_hda_intel

	Kernel modules: snd-hda-intel

00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)

00:14.5 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 0

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 1

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 2

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 3

	Kernel driver in use: k10temp

	Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 4

00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 5

02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01)

	Subsystem: Hewlett-Packard Company Device 1838

	Kernel driver in use: ath9k

	Kernel modules: ath9k

04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01)

	Subsystem: Hewlett-Packard Company Device 1849

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

	Subsystem: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller

	Kernel driver in use: r8169

	Kernel modules: r8169

Wszystko fajnie, pięknie, ale chodziło mi to, żebyś te wyniki podał mi jak podłączasz się kablem, bo widać, że jesteś połączony z siecią WiFi i nie ma z nią żadnych problemów. Podaj jeszcze raz te same wyniki, ale z podłączonym kablem sieciowym i rozłączonym WiFi.

eth0 Link encap:Ethernet HWaddr 28:92:4a:3f:6f:2b  

          inet6 addr: fec0::8:2a92:4aff:fe3f:6f2b/64 Scope:Site

          inet6 addr: 2002:9c11:ef33:8:2a92:4aff:fe3f:6f2b/64 Scope:Global

          inet6 addr: fe80::2a92:4aff:fe3f:6f2b/64 Scope:Link

          inet6 addr: fec0::8:9ccf:5e6b:2533:479a/64 Scope:Site

          inet6 addr: 2002:9c11:ef33:8:9ccf:5e6b:2533:479a/64 Scope:Global

          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

          RX packets:8963 errors:0 dropped:0 overruns:0 frame:0

          TX packets:961 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:656504 (656.5 KB) TX bytes:210334 (210.3 KB)

          Interrupt:47 Base address:0x8000 


lo Link encap:Local Loopback  

          inet addr:127.0.0.1 Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING MTU:16436 Metric:1

          RX packets:44333 errors:0 dropped:0 overruns:0 frame:0

          TX packets:44333 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:4065475 (4.0 MB) TX bytes:4065475 (4.0 MB)


wlan0 Link encap:Ethernet HWaddr 74:e5:43:8f:39:a2  

          UP BROADCAST MULTICAST MTU:1500 Metric:1

          RX packets:1731797 errors:0 dropped:0 overruns:0 frame:0

          TX packets:1159056 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:2088728758 (2.0 GB) TX bytes:135578727 (135.5 MB)

NetworkManager Tool


State: disconnected


- Device: eth0 -----------------------------------------------------------------

  Type: Wired

  Driver: r8169

  State: disconnected

  Default: no

  HW Address: 28:92:4A:3F:6F:2B


  Capabilities:

    Carrier Detect: yes

    Speed: 100 Mb/s


  Wired Properties

    Carrier: on



- Device: wlan0 ----------------------------------------------------------------

  Type: 802.11 WiFi

  Driver: ath9k

  State: disconnected

  Default: no

  HW Address: 74:E5:43:8F:39:A2


  Capabilities:


  Wireless Properties

    WEP Encryption: yes

    WPA Encryption: yes

    WPA2 Encryption: yes


  Wireless Access Points 

    Nibylandia: Infra, 00:1F:1F:7A:C2:94, Freq 2462 MHz, Rate 54 Mb/s, Strength 29 WPA2

    Cyganski Alibaba:Infra, C0:3F:0E:88:87:FC, Freq 2417 MHz, Rate 54 Mb/s, Strength 40 WPA2

    tepek: Infra, D8:5D:4C:BE:E4:14, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2

    TYLKO_DLA_LUDZI: Infra, 74:EA:3A:AD:D2:A8, Freq 2462 MHz, Rate 54 Mb/s, Strength 25 WPA2

    default: Infra, 00:26:18:D9:0C:5F, Freq 2422 MHz, Rate 54 Mb/s, Strength 20

Kernel IP routing table

Destination Gateway Genmask Flags Metric Ref Use Iface

uzytkownik@HP-Pavilion:~$ ping -c 4 dobreprogramy.pl

ping: unknown host dobreprogramy.pl

uzytkownik@HP-Pavilion:~$ ping -c

ping: option requires an argument -- 'c'

Usage: ping [-LRUbdfnqrvVaAD] [-c count] [-i interval] [-w deadline]

            [-p pattern] [-s packetsize] [-t ttl] [-I interface]

            [-M pmtudisc-hint] [-m mark] [-S sndbuf]

            [-T tstamp-options] [-Q tos] [hop1 ...] destination

00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Complex

	Subsystem: Hewlett-Packard Company Device 1849

00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Device 9990

	Subsystem: Hewlett-Packard Company Device 1849

00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel modules: snd-hda-intel

00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Root Port

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:10.0 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: xhci_hcd

00:10.1 USB controller: Advanced Micro Devices [AMD] Hudson USB XHCI Controller (rev 03)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: xhci_hcd

00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller [AHCI mode]

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ahci

00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ehci_hcd

00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ehci_hcd

00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 14)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel modules: i2c-piix4

00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: snd_hda_intel

	Kernel modules: snd-hda-intel

00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)

00:14.5 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI Controller (rev 11)

	Subsystem: Hewlett-Packard Company Device 1849

	Kernel driver in use: ohci_hcd

00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1

	Kernel driver in use: pcieport

	Kernel modules: shpchp

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 0

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 1

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 2

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 3

	Kernel driver in use: k10temp

	Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 4

00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 15h (Models 10h-1fh) Processor Function 5

02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01)

	Subsystem: Hewlett-Packard Company Device 1838

	Kernel driver in use: ath9k

	Kernel modules: ath9k

04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01)

	Subsystem: Hewlett-Packard Company Device 1849

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

	Subsystem: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller

	Kernel driver in use: r8169

	Kernel modules: r8169

uzytkownik@HP-Pavilion:~$ traceroute

Program 'traceroute' można znaleźć w następujących pakietch:

 * inetutils-traceroute

 * traceroute

Spróbuj: sudo apt-get install

Wygląda na to, że na kablu uzyskujesz tylko adres IPv6. Pokaż wyniki poniższych poleceń.

cat /etc/network/interface

cat /etc/modprobe/blacklist.conf

cat /etc/sysctl.conf

cat /etc/hosts

dhclient eth0

Rozumiem, że bezprzewodowo łączysz się z tą samą siecią? Jeśli tak, to zobacz co będzie jak przypiszesz adres statycznie, tzn. ręcznie.

Łączę się z inną siecią bezprzewodową.

cat: /etc/network/interface: Nie ma takiego pliku ani katalogu

cat: /etc/modprobe/blacklist.conf: Nie ma takiego pliku ani katalogu

#

# /etc/sysctl.conf - Configuration file for setting system variables

# See /etc/sysctl.d/ for additional system variables

# See sysctl.conf (5) for information.

#


#kernel.domainname = example.com


# Uncomment the following to stop low-level messages on console

#kernel.printk = 3 4 1 3


##############################################################3

# Functions previously found in netbase

#


# Uncomment the next two lines to enable Spoof protection (reverse-path filter)

# Turn on Source Address Verification in all interfaces to

# prevent some spoofing attacks

#net.ipv4.conf.default.rp_filter=1

#net.ipv4.conf.all.rp_filter=1


# Uncomment the next line to enable TCP/IP SYN cookies

# See http://lwn.net/Articles/277146/

# Note: This may impact IPv6 TCP sessions too

#net.ipv4.tcp_syncookies=1


# Uncomment the next line to enable packet forwarding for IPv4

#net.ipv4.ip_forward=1


# Uncomment the next line to enable packet forwarding for IPv6

# Enabling this option disables Stateless Address Autoconfiguration

# based on Router Advertisements for this host

#net.ipv6.conf.all.forwarding=1



###################################################################

# Additional settings - these settings can improve the network

# security of the host and prevent against some network attacks

# including spoofing attacks and man in the middle attacks through

# redirection. Some network environments, however, require that these

# settings are disabled so review and enable them as needed.

#

# Do not accept ICMP redirects (prevent MITM attacks)

#net.ipv4.conf.all.accept_redirects = 0

#net.ipv6.conf.all.accept_redirects = 0

# _or_

# Accept ICMP redirects only for gateways listed in our default

# gateway list (enabled by default)

# net.ipv4.conf.all.secure_redirects = 1

#

# Do not send ICMP redirects (we are not a router)

#net.ipv4.conf.all.send_redirects = 0

#

# Do not accept IP source route packets (we are not a router)

#net.ipv4.conf.all.accept_source_route = 0

#net.ipv6.conf.all.accept_source_route = 0

#

# Log Martian Packets

#net.ipv4.conf.all.log_martians = 1

#

uzytkownik@HP-Pavilion:~$ cat /etc/hosts

127.0.0.1	localhost

127.0.1.1	HP-Pavilion


# The following lines are desirable for IPv6 capable hosts

::1 ip6-localhost ip6-loopback

fe00::0 ip6-localnet

ff00::0 ip6-mcastprefix

ff02::1 ip6-allnodes

ff02::2 ip6-allrouters

uzytkownik@HP-Pavilion:~$ dhclient eth0

RTNETLINK answers: Operation not permitted

Masz możliwość połączenia się z tą siecią, co łączysz się po kablu, bezprzewodowo?

Mój błąd (przyzwyczajony jestem do automatycznego uzupełniania poleceń), powinno być

cat /etc/network/interfaces

cat /etc/modprobe.d/blacklist.conf

Tutaj też mój błąd, powinno być

sudo dhclient eth0

Niestety tez nie

auto lo

iface lo inet loopback

uzytkownik@HP-Pavilion:~$ cat /etc/modprobe.d/blacklist.conf

# This file lists those modules which we don't want to be loaded by

# alias expansion, usually so some other driver will be loaded for the

# device instead.


# evbug is a debug tool that should be loaded explicitly

blacklist evbug


# these drivers are very simple, the HID drivers are usually preferred

blacklist usbmouse

blacklist usbkbd


# replaced by e100

blacklist eepro100


# replaced by tulip

blacklist de4x5


# causes no end of confusion by creating unexpected network interfaces

blacklist eth1394


# snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much

# hardware on its own (Ubuntu bug #2011, #6810)

blacklist snd_intel8x0m


# Conflicts with dvb driver (which is better for handling this device)

blacklist snd_aw2


# causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306)

blacklist i2c_i801


# replaced by p54pci

blacklist prism54


# replaced by b43 and ssb.

blacklist bcm43xx


# most apps now use garmin usb driver directly (Ubuntu: #114565)

blacklist garmin_gps


# replaced by asus-laptop (Ubuntu: #184721)

blacklist asus_acpi


# low-quality, just noise when being used for sound playback, causes

# hangs at desktop session start (Ubuntu: #246969)

blacklist snd_pcsp


# ugly and loud noise, getting on everyone's nerves; this should be done by a

# nice pulseaudio bing (Ubuntu: #77010)

blacklist pcspkr


# EDAC driver for amd76x clashes with the agp driver preventing the aperture

# from being initialised (Ubuntu: #297750). Blacklist so that the driver

# continues to build and is installable for the few cases where its

# really needed.

blacklist amd76x_edac

a w tej ostatniej komendzie zapytało mnie tylko o haslo i nic nie pokazalo

Podłącz się kablem, nie łącz się z inną siecią bezprzewodową i pokaż jeszcze raz wynik poleceń.

ifconfig eth0

ip link show dev eth0

ip -6 route

Na chwilę obecną wygląda to tak, że w sieci, do której się podłączasz skonfigurowany jest tylko protokół IPv6, przypisywany jest Ci adres routowalny, więc sieć mimo wszystko powinna działać. Sprawdzałeś w akademiku czy wyniki są takie same?

Jeśli chodzi Ci o porównanie wyników dom-akademik to będę mógł to zrobić nie wcześniej niż w środę wieczorem.

eth0 Link encap:Ethernet HWaddr 28:92:4a:3f:6f:2b  

          inet6 addr: fec0::c:2a92:4aff:fe3f:6f2b/64 Scope:Site

          inet6 addr: 2002:9c11:ef5f:c:2a92:4aff:fe3f:6f2b/64 Scope:Global

          inet6 addr: fe80::2a92:4aff:fe3f:6f2b/64 Scope:Link

          inet6 addr: fec0::c:144f:9617:a7b5:d758/64 Scope:Site

          inet6 addr: 2002:9c11:ef5f:c:144f:9617:a7b5:d758/64 Scope:Global

          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

          RX packets:53985 errors:0 dropped:0 overruns:0 frame:0

          TX packets:2656 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:4038706 (4.0 MB) TX bytes:555208 (555.2 KB)

          Interrupt:47 Base address:0x8000

2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000

    link/ether 28:92:4a:3f:6f:2b brd ff:ff:ff:ff:ff:ff

2002:9c11:ef5f:c::/64 dev eth0 proto kernel metric 256 expires 7190sec

fe80::/64 dev eth0 proto kernel metric 256 

fec0:0:0:c::/64 dev eth0 proto kernel metric 256 expires 7190sec

default via fe80::c0cb:ca97:6698:9977 dev eth0 proto kernel metric 1024 expires 65528sec

Co do komendy sudo dhclient eth0 ciagle pyta mnie tylko o haslo i nic nie pokazuje. Oczywiście wpisuje z podpiętym kablem.

Wygląda na to, że w sieci, z której korzystasz nie działa protokół IPv4, system nie może również znaleźć serwera DHCP, który przydziela adres IPv4. Uzyskujesz globalne adresy IPv6. Popytaj administratora/dostawcę z jakiej wersji protokołu IP korzysta sieć, wtedy będzie wiadomo na czym stoimy.

Na Windowsie również ten problem występuje? Jeśli nie, uruchom wiersz poleceń systemu Windows i podaj mi wyniki poniższych poleceń kopiowanie-wynikow-polecen-wiersza-polecen-windows-t499881.html

ipconfig /all

netsh interface ip show config

route print

Oczywiście przy podłączonym kablu sieciowym.

Jak miałem Windowsa wszystko działało bezproblemowo. Jednak zdecydowałem się na całkowitą zmianę i mam teraz tylko Linuxa.

Usage: route [-nNvee] [-FC] [] List kernel routing tables

       route [-v] [-FC] {add|del|flush} ... Modify routing table for AF.


       route {-h|--help} [] Detailed usage syntax for specified AF.

       route {-V|--version} Display version/author and exit.


        -v, --verbose be verbose

        -n, --numeric don't resolve names

        -e, --extend display other/more information

        -F, --fib display Forwarding Information Base (default)

        -C, --cache display routing cache instead of FIB

=Use '-A ' or '--'; default: inet

  List of possible address families (which support routing):

    inet (DARPA Internet) inet6 (IPv6) ax25 (AMPR AX.25) 

    netrom (AMPR NET/ROM) ipx (Novell IPX) ddp (Appletalk DDP) 

    x25 (CCITT X.25)

Pozostałe komendy mi nie działają.

Wysłałem maila i czekam na odpowiedź.

Bo one działają na Windowsie, a te wyniki poleceń chciałem z Windows o czy pisałem,

bo myślałem, że z niego również korzystasz.

Jak będziesz coś wiedział, to daj znać.