Witam. Ostatnio zainstalowałem najnowsze Ubuntu i postanowiłem zrobić coś z hałasem jaki od pewnego czasu wydowbywa się z bebechów mojego laptopa. Znalazłem poradnki, w którym opisano jak można kontrolować obroty wiatraczka na CPU, ale w pewnym momencie coś mi nie działa. Wspomniany artykuł można znaleźć tutaj: http://forum.ubuntu.pl/showthread.php?t=88587 A zacinam się w miejscu, gdzie trzeba wpisać “sudo pwmconfig”, ponieważ wyskakuje mi taki komunikat: “There are no pwm-capable sensor modules installed”. Co mogłem zrobić źle?
Tutaj można zobaczyć moje zmagania z tym:
kamileon@kamileon-Aspire-5710Z:~$ sudo sensors-detect
[sudo] password for kamileon:
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: Acer Aspire 5710Z (laptop)
# Board: Acer Acadia
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... Success!
(driver `coretemp')
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 82801G ICH7
Module i2c-i801 loaded successfully.
Module i2c-dev loaded successfully.
Next adapter: Radeon i2c bit bus VGA (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Next adapter: Radeon i2c bit bus LVDS (i2c-1)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: Radeon i2c bit bus DVI (i2c-2)
Do you want to scan it? (YES/no/selectively): y
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `coretemp':
* Chip `Intel Core family thermal sensor' (confidence: 9)
To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!
Do you want to add these lines automatically to /etc/modules? (yes/NO)y
Successful!
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.
Unloading i2c-dev... OK
Unloading i2c-i801... OK
kamileon@kamileon-Aspire-5710Z:~$ sudo /etc/init.d/module-init-tools start
Rather than invoking init scripts through /etc/init.d, use the service(8)
utility, e.g. service module-init-tools start
Since the script you are attempting to invoke has been converted to an
Upstart job, you may also use the start(8) utility, e.g. start module-init-tools
module-init-tools stop/waiting
kamileon@kamileon-Aspire-5710Z:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
lp
# Generated by sensors-detect on Thu Oct 14 02:29:00 2010
# Chip drivers
coretemp
# Generated by sensors-detect on Thu Oct 14 02:51:38 2010
# Chip drivers
coretemp
# Generated by sensors-detect on Thu Oct 14 03:11:40 2010
# Chip drivers
coretemp
# Generated by sensors-detect on Thu Oct 14 03:14:10 2010
# Chip drivers
coretemp
kamileon@kamileon-Aspire-5710Z:~$
Z góry dzięki za pomoc.